EFTA00727790

FA MARKZEFF LITTLE SAINT JAMES KITCHEN FINISH SPECIFCATIONS October 20, 2010 515 WEST 20TH ST, 4W NEW YORK, NY 10011 P 212.624.4004 F 212.624.4008 markzeftcom EFTA00727790 IA MARK ZEFF Project Name: LITTLE SAINT JAMES Item Number: HD-01 Project #: LS3-01 Item Description: SMALL CABINET PULL Issue Date: Item Quantity: Manufacturer: Hafele Source: Address: 25 East 26th Address: New York, NY 10011- Phone: 800# : (800) 423-3531 Phone: Fax: Fax: Contact: Contact: E-mail: E-mail: Web: www.hafele.com Web: Model Number: 117.05.600 Model Name: SMALL PULL - 146MM Dimensions: REFER TO CUTSHEET Color/Finish: STAINLESS STEEL/MATTE FINISH Required Item(s) for Designer Approval Prior to Fabrication: Seaming Diagram Strike-Off Finish Sample Cutting Shop Dwgs Prototype Flame Certificate Instructions: • Image is for reference only. • All metal to be non-corrosive. • Contractor is to assume responsibility for preparing surfaces and using appropriate techniques and installation methods as required by manufacturer prior to installation. Page 1 HD-01 Mark Zeff 515 W 20th St, 4W New York, NY 10011 p www.markzeff.com EFTA00727791 Call 1-800-423-3531 anywhere in Canada - www.hafele.com'm HAFELE Stainless Steel Handles Matt Threaded Screws 8.32 Size A Dimension C Cat. No. Combined slot, suitable for flat or cross blades. 146 96 117.05.600 Fnish: steel, yellow chrcmated 178 128 117.05.610 Length Cat. No. 242 192 117.05.620 10 mm 022.35.109 274 224 117.05.630 12 mm 022.35.127 370 320 117.05.640 15 mm 022.35.154 530 480 117.05.650 18 mm 022.35.181 722 672 117.05.660 20 mm 022.35.207 946 896 117.05.670 22 mm 022.35.225 Packing: 5 and 10 pcs. 23 mm 022.35.234 25 mm 022.35.252 Paddng: 1000 pcs. Matt, 3 bases 28 mm 022.35.289 Size Hole Spacing Cat. No. 30 mm 022.35.305 A C C1 35 mm 022.35.350 1202 1152 576 117.05.680 38 mm 022.35.387 1456 1408 704 117.05.690 40 mm 022.35.403 45 mm 022.35.458 Packhg: 10 pcs. 50 mm 022.35.501 52 mm 022.35.520 55 mm 022.35.550 60 mm 022.35.609 Packing: 500 pcs. 75 mm 022.25.750 80 mm 022.25.800 85 mm 022.25.850 90 mm 022.25.900 95 mm 022.25.950 100 mm 022.25.990 Matt Paddng: 100 pcs. Size A Dimension B Cat. No. 136 96 115.84.001 168 128 115.84.002 200 160 115.84.003 _1111041ttl 0 328 288 115.84.004 Threaded Breakoff Screw M4 Packing: 10 pcs. (M4 25 mm mounting screws itch.) Combined slot. suitable for flat or cross blades. Fnish: steel, zinc-plated Length Cat. No. x 022.35.887 Paddng: 100 and 500 pcs. Dimensional data not bincirg. We resew the right to alter specifications without notice. Dimensions in mm 2 inches are approximate EFTA00727792 IA MARK ZEFF Project Name: LIME SAINT JAMES Item Number: HD-02 Project #: LS3-01 Item Description: LARGE CABINET PULL Issue Date: Item Quantity: Manufacturer: Hafele Source: Address: 25 East 26th Address: New York, NY 10011- Phone: 800# : (800) 423-3531 Phone: Fax: Fax: Contact: Contact: E-mail: E-mail: Web: www.hafele.com Web: Model Number: 117.05.660 Model Name: LARGE PULLL - 722MM Dimensions: REFER TO CUTSHEET Color/Finish: STAINLESS STEEL/MATTE FINISH Required Item(s) for Designer Approval Prior to Fabrication: Seaming Diagram Strike-Off Finish Sample Cutting Shop Dwgs Prototype . Flame Certificate Instructions: • Image is for reference only. • All metal to be non-corrosive. • Contractor is to assume responsibility for preparing surfaces and using appropriate techniques and installation methods as required by manufacturer prior to installation. Page 1 HD-02 Mark Zeff 515 W 20th St, 4W New York, NY 10011 p www.markzeff.com EFTA00727793 Call 1-800-423-3531 anywhere in Canada - www.hafele.com'm HAFELE Stainless Steel Handles Matt Threaded Screws 8.32 Size A Dimension C Cat. No. Combined slot, suitable for flat or cross blades. 146 96 117.05.600 Finish: steel, yellow chrcmated 178 128 117.05.610 Length Cat. No. 242 192 117.05.620 10 mm 022.35.109 274 224 117.05.630 12 mm 022.35.127 370 320 117.05.640 15 mm 022.35.154 530 480 117.05.650 18 mm 022.35.181 722 672 117.05.660 20 mm 022.35.207 946 896 117.05.670 22 mm 022.35.225 Packing: 5 and 10 pcs. 23 mm 022.35.234 25 mm 022.35.252 Packing: 1000 pcs. Matt, 3 bases 28 mm 022.35.289 Size Hole Spacing Cat. No. 30 mm 022.35.305 A C C1 35 mm 022.35.350 1202 1152 576 117.05.680 38 mm 022.35.387 1456 1408 704 117.05.690 40 mm 022.35.403 45 mm 022.35.458 Packhg: 10 pcs. 50 mm 022.35.501 52 mm 022.35.520 55 mm 022.35.550 60 mm 022.35.609 Packing: 500 pcs. 75 mm 022.25.750 80 mm 022.25.800 85 mm 022.25.850 90 mm 022.25.900 95 mm 022.25.950 100 mm 022.25.990 Matt Packing: 100 pcs. Size A Dimension B Cat. No. 136 96 115.84.001 168 128 115.84.002 EDI Threaded Breakoff Screw 144 200 328 160 288 115.84.003 115.84.004 Packing: 10 pcs. (M4 25 mm mounting screws incl.) Combined slot, suitable for flat or cross lades. Friish: steel, zinc-plated Length Cat. No. 1V4- x V.- 022.35.887 Packing: 100 and 500 pcs. Ctmensonal data not bindr.g. We resew the right to alter specthcattons without notice. Dimensions in mm 2 Inches are approximate EFTA00727794 Project Name: LITTLE SAINT JAMES Item Number: LT-01 Project #: LS3-01 Item Description: PENDANT LIGHT - KITCHEN Issue Date: Item Quantity: Manufacturer: Restoration Hardware Source: Address: Address: Phone: Phone: Fax: Fax: Contact: Contact: E-mail: E-mail: Web: www.restorationhardware.com Web: Description: DECORATIVE KITCHEN PENDANT LIGHT FIXTURE Model Number: 68070201 Model Name: 18" KEYNES PRISM SINGLE PENDANT Dimensions: 18" DIAMETER x 27.5"H Finish: ALUMINUM Lamp Wattage: 60W Pit Required Item(s) for Designer Approval Prior to Fabrication: Seaming Diagram Strike-Off Finish Sample Cutting Shop Dwgs Prototype Flame Certificate Instructions: • The Contractor must coordinate with the manufacturer exact specifications on sockets, lamping, and ADA requirements to ensure decorative light fixtures meet all local, state, and federal codes for applicable conditions. • Property owner is responsible for purchasing and supplying all lamps (bulbs) required for all specified fixtures. tamping requirements must not exceed the maximum wattage as specified for each fixture. Page 1 LT-01 Mark Zeff 515 W 20th St, 4W New York, NY 10011 p www.markzeff.com EFTA00727795 Project Name: LITTLE SAINT JAMES Item Number: LT-02 Project #: LSJ-01 Item Description: UNDERCABINET PUCK LIGHT Issue Date: Item Quantity: Manufacturer: Lucifer Lighting Source: Address: 3750 IH•35 North Address: San Antonio, TX 78219- Phone: (210) 227-7329 Phone: Fax: (210) 227-7329 Fax: Contact: Contact: E-mail: E-mail: Web: www.luciferlighting.com Web: Description: UNDERCABINET PUCK LIGHT FIXTURE Model Number: LPK-12-10-W Model Name: UNLENSED RECESSED PUKLIGHT Dimensions: REFER TO CUTSHEET Finish: WHITE/MATTE Required Item(s) for Designer Approval Prior to Fabrication: Seaming Diagram Strike-Off Finish Sample Cutting Shop Dwgs Prototype Flame Certificate Instructions: • The Contractor must coordinate with the manufacturer exact specifications on sockets, lamping, and ADA requirements to ensure decorative light fixtures meet all local, state, and federal codes for applicable conditions. • Property owner is responsible for purchasing and supplying all lamps (bulbs) required for all specified fixtures. Lamping requirements must not exceed the maximum wattage as specified for each fixture. Page 1 LT-02 Mark Zeff 515 W 20th St, 4W New York, NY 10011 p www.markzeff.com EFTA00727796 PUKLIGHT ® PRODUCT SPECIFICATION LENSED Catalog No. Finish Lamp LPK-I 2-I0-W Matte white Quartz halogen. I2v I Ow Max LPK-I2-I0-B Matte black Quartz halogen, I2v I Ow Max RECESSED SURFACE LPK-I2-I0-C Satin chrome Quartz halogen. I2v I Ow Max LPK-I2-I0-G Satin brass Quartz halogen. I2v I Ow Max (see mverse side for complete list ofPukbght Catalog Nos) LOW VOLTAGE SIDE 2.94' (Mem) dtmeur— MINI-DOWNLIGHT Iw 2.26' (37.4tren) clamour - 0•I SY AO' (2.23rren) (IS.0mm) UnInsed I.20r (305mm) Lamed E*— 2.72' (A I corn) darnoter BOTTOM TOP 3 holds no. apart OA COM/ —4. 225" (57.2mm) bolt Cltd0 GENERAL DESCRIPTION LABEL Low voltage palm-size lighting fixture with unique twist-on lens retainer. U.L. Listed Class II. File No. E 141044, when ordering a lensed Puklight It can accommodate (I) lens accessory only. A 12v l0w maximum bi- with a plug-in transformer. ETL Listed Class II when ordering a lensed pin G4 base quartz halogen lamp is standard. Relamping is done from PiAlight with a wire•in transformer. front of fixture after 1/4 turn and removal of lens retainer. Fixtme can be recessed or surface mounted. Clear or frosted lens available. ELECTRICAL Fixture is pre-wired with 18 AWG 200°C wire exiting from the side of MOUNTING the fixture. 6' pigtails are provided for easy connections. If recessed, the fixture is mounted in a hole 2 1/4' in diameter and 5/8" deep using three screws through the mounting holes provided. OPTIONS Fixture available in ready-to-install kits of I to 6 Puktights. Kits include: MATERIAL I Ow quartz halogen lamps and one 12v 60w wire-in or plug-in Housing and him are high temperature injection molded thermoplastic. electronic transformer. Transformers are Class II U.L Approved. Reflector is plated die cast metal. Lens is tempered glass, Wire is teflon Accessories include black honeycomb louver and colored lenses, Bi•pin coated high temperature stranded wire. xenon I2v I Ow maximum lamp in clear or frosted also available. (refer to reverse side for ordering information). FINISH Matte White PATENTS Matte Black U.S. and foreign patents. Satin Chrome Satin Brass LUCIER Laat-rriNa comowsry 414 Live Oak Street O2002 Lucifer Lighting Company San Antonio. Texas 78202 As part of its policy of continuous research and product development, the Phone 210 227-7329 Company reserves the right to change or withdraw specifications without FAX 210 227-4967 prior notice. www.lutlferlIghtIng.com 097 I .0502 EFTA00727797 PUKLIGHT ® LENSED PHOTOMETRICS - PUKLIGHT with Clear Lens INSTALLATION I2V POWER SOURCE MOUNTING SURFACE — SURFACE COLLAR Oar optional Sorlan Mount installation) PHOTOMETRICS - PUKLIGHT with Frosted Lens — PUKLIGHT MOUSING with LAMP mu r O. a ...• o on $ IC 97 as 9 03 'MO On 1 - SCREWS is 44 II I3 NI3 443 It 4., 15 34 14 IA 443 43/ 20 a I. 153 4 — TRIM RING 33 13 II 40 II ZS H2 lig 45 II Ill IN so 34 ss a IS $2 133 LENS or so LOUVER ss 4 44 33 IN 70 43 50 In 73 2 00 10 40 III 45 I — LENS RETAINING RING SA 33 ILI SO ii3421 *Mr! A SC • • 40 10 147 0 Lvov San= AC Setaid* Ann o nnanly were& Kong folpso pee nannon .bay. 40•011VCr to can $1011moilIOSOk.muntenontlqww fa oriel mmeitneninst antis4(ox. 048md (aossalksa icia ORDERING Catalog No. Desalpdon PUKLIGHT with Clear Lens LPK-12-10-• Recessed Puldight housing, trim ring with clear Sass lens. and 12v l0w halogen lamp LPK-SC-12-10-* Surface Puklight housing, trim ring with dear glass lens, surface moult collar. and I2v I Ow halogen lamp PUKLIGHT CLEAR LENS KITS LPKT-I-* I fixture & 12v 60w wire-in electronic transformer with clear lens, surface mount LPKT-2-* 2 fixtures & 12v 60w wire-in electronic transformer collar, and 12v, I Ow halogen LPKT-3-* 3 fixtures & 12v 60w wire-in electronic transformer lamps LPKT-4-* 4 fixtures & 12v 60w wire-in electronic transformer LPKT-5-* 5 fixtures & 12v 60w wire-in electronic transformer LPKT-6-* 6 fudures & 12v 60w wire-in electronic transformer Note: To substitute f 2v 50w piag,in elearonk tronsfeinler, use LPICP prefix instead ofLPKT prep PUKLIGHT with Frosted Lens FPK-12-10-* Recessed Puldight housing, trim ring with frosted glass lens and 12v l0w halogen lamp EPIC-SC-12-10-* Surface Puklight housing, trim ring with frosted glass lens, surface mount collar. and 12v l0w halogen lamp PUKLIGHT FROSTED LENS FPKT-I-* I future & 12v 60w wire-in electronic transformer KITS with frosted lens, surface FPKT-2-* 2 Mures & 12v 60w wire-in electronic transformer mount collar, and I2v, l0w FPKT-3-* 3 factures & 12v 60w wire-in electronic transformer halogen lamps FPKT-4-* 4 fixtures & 12v 60w wire-in electronic transformer FPKT-5-* 5 fixtures & 12v 60w wire-in electronic transformer FPKT-6-* 6 fixtures & 12v 60w wire-in electronic transformer Note: To substitute f 2v 60w piag,in elearonk transiently use FPICP prefix instead ofFPKT prefix LAMP OPTIONS 12-05-XH-** 12 volt 5 watt, bi-pin xenon lamp 12-10-XH-** 12 volt 10 watt, bi-pin xenon lamp ACCESSORIES FGL-3 Frosted glass lens CGL-3 Clear glass lens (Louvers and colored lens HCL-3 Honeycomb louver (black) - 45° glare cut off accessories for use with a lensed GL-B Glass lens - blue Puldight only) GL-G Glass lens - green GL-R Glass lens - red WMC-1110 Wire moulting dip - to fasten wire to wall or surface - 10 per pack WC-I/10 Wire connector and splice adapter - 10 per pack W-I8/2-10 Installation wire - 18 gauge/2 conductors - 10 ft. length • Sperjf, air cob/ pet catabp number: W • Matte whore B • Moue Ina& C Senn chrome G. Soon brass •• Specify: a • CS, FR • frosted EFTA00727798 PUKL IGHT° LENSED PUKLIGHT FLUSH OR SURFACE MOUNT INSTALLATION I2V POWER SOURCE LENSED & UNLENSED I. Follow WARNINGS and Technical Information on Lamping and Wiring (see reverse side). MOUNTING 2. If recessed, cut a hole in SURFACE INSTALLATION MOUNTING SURFACE 2 IN' (57mm) in diameter Before beginning any PVIBLICI4T W (see template). OF T installation, disconnect electrical power WF SURFACE COLLAR 3. Remove LENS RETAINING (for optional Surface at a main switch or circuit breaker. Round dorm to the nearest whole make RING with LENS or LOUVER Mount Installation) Where PE . Total quantity of Palmerton' translomm by rotating counterclockwise LIGHTED LAMP IS HOT! 114 turn. WT Wattage rating of transform., To reduce the risk of FIRE, BURNS. and Wattage of lades per finale PUKLIGHT NOUSrhic (maximum wattage per fixture e IC MRS: 4. Remove the TRIM RING from with LAMP EYE DAMAGE EXNAITILE. the PUKLIGHT by gently I. Read all instructions before attempting WT. 60 watts prying the prongs from their any installation. VP- IP watts slots. SCREWS 2. Disconnect and allow to cool for at Asv n S. OPTION: for surface mount Or. .6 Axioms law installation. slide the least 5 minutes before replacing bulb. TRIM RING mown% down tt the news NUM( SURFACE COLLAR over the 3. Bulb gets HOT quickly! Be sure the maximum of six finites ler the/enmity* PUKLIGHT housing. power is off when relamping. 4. Do not touch hot lens, louver, or LAMP SELECTION. PUKLIGHT is a 6. Using the 3 screws provided. e- Th LENS or low voltage lighting fixture designed to anchor the PUKLIGHT (and LOUVER enclosure. SURFACE COLLAR) to the operate with a 12-volt power supply only. 0 5. Do not direct light at persons. Use only with a I2-volt bare halogen lamp. MOUNTING SURFACE. LENS RETAINING RING 6. Do not look directly at lighted bulb. 10 watts maximum. 7. Reaffix the TRIM RING by gently snapping into place. 7. Keep lamp away from curtains. draperies, and similar materials. POWER SOURCE. The power supply 8. Replace LENS RETAINING 8. Use only with a 10 watt or smaller is typically a remote 12-volt transformer RING and LENS or LOUVER which is installed between the 120-volt to the PUKUGHT HOUSING bulb. and secure by rotating 114 electrical supply and the PUKLIGHT. 9. Do not touch the bulb at any time. cam clockwise. Use a soft cloth. Oil from skin may NOTE: damage bulb integrity. For lamp installation. refer to 10. The lensed fixture is provided with a Technical Information-Lamping glass lens or louver to protect the (see reverse side) PUKUGHT IS UL LISTED WHEN user from the excessive heat of the LENSED AND USED WITH PLUG- bulb and from particles of glass should IN TRANSFORMER. bulb rupture occur. To reduce the risk of burns, do not operate the lamp without the lens or louver secured in PUKUGHT IS En LISTED WHEN place. Damaged glass lens or louver LENSED AND USED WITH PLUG- should be replaced before the lamp is O IN OR HARD-WIRE used. TRANSFORMER II. Use the following formula to determine die total number of fixtures that can be connected to each transformer: SAVE THESE INSTRUCTIONS. 1 LUCIFER LIGHTING COMPANY 2 EFTA00727799 UNLENSED PUKUGHT FLUSH OR SURFACE MOUNT Inv POWER SOURCE TECHNICAL INFORMATION INSTALLATION I. Follow WARNINGS and Technical Information on LAMPING. Remove LENS RETAINING DIMMING. PUKUGHT may be dimmed Lamping and Wiring (see RING (unless UNLENSED) with LENS or through use of appropriate controls reverse side). LOUVER by rotating counterclockwise 1/4 installed in the primary circuit of the CEILING turn. Trim need not be removed for transformer. All transformers must have 2. If recessed, cut a hole in relamping. Use tissue or soft cloth for clean voltage wave shapes applied to them MOUNTING SURFACE 2 lee (S7mtn) in diameter inserting lamp. Hand contact with lamp to prevent overheating and burn-out. (see template). diminishes lamp life. Be sure power Is off Standard household-type dimmers which and allow lamp to cool at least 5 minutes phase-dip the voltage wave will burn out 3. Remove the TRIM RING from ACCESSORY RING (for optional Surface before relamping. both the transformer and the dimmer. the PUKLIGHT by gently mount installation) prying the prongs from their WIRING. LENSED PUKLIGHT is a UL WARNING: Co not use incandescent or slots. Usted. Class II, low voltage lighting fixture fluorescent dimmers with PUNLIGHTI PUKLIGITT when used with a plug-in transformer. It is Use only dimmers expressly identified 4. OPTION: for surface mount ETL Usted. Class II, when used with a plug- installation. slide the for dimming law voltage magnetic SURFACE COLLAR over the in or hardwire transformer. It is designed transformers. PUKLIGHT housing. SCREWS to work with a 12-Volt power supply only. Use only with a 12-Volt 10-Watt lamp WARNING: PUKUGHT WHEN LIT WITH S. Using the 3 screws provided. maximum. A typical Installation requires a HALOGEN LAMP IS EXTREMELY HOW anchor the PUKLIGHT (ond transformer between the 120-Volt SURFACE COLLAR) to the TRIM RING To avoid risk of fire, burns and eye MOUNTING SURFACE. electrical supply and the Puklight fixture. damage: When Puldights are installed alone or in tandem, the power supply (I.e.. 1. Do not touch lamp when lit: do not 6. Reaffix the TRIM RING by gently snapping into place. transformer in typical installation) must be direct light at persons and do not protected with an in-line circuit breaker or look directly at lighted lamp. NOTE: fuse that Is properly sized to load. Lucifer 2. Disconnect and allow fixture to cool For lamp installation. refer to transformer models ET60-12 and ETI50- at least 5 minutes before replacing Technical Information-Lamping 12 (hardwire) and ETP60-12 (plug-in) have lamp. (see reverse side) built-in short circuit protection. 3. Do not place fixture near curtains, An Installation using from I to 6 Puklights. draperies and in unventilated or 10 watts each, requires a 60-watt confined areas. transformer, 18 gauge wire no more than 10 feet In length and fuse or circuit breaker. Consult an electrical engineer if more than 6 Puklights are to be Installed In multiple fused circuits. See diagram for connection and fusing below: PUKLIGHT SINGLE UNIT 120401(ntni awn 9waNtnen 12400eatial PUKLIGHT N TANDEM 1111Wilar 120•Vali:Waft boa tagwatwa 12•Val Sofeedan IPAMWOPM. tomanixnalt peon image.. Nnea amtnel Inv+. aspant wad to swap Warn/WM /DOM n al/WANT NJ Warn. Ilxal Strenlat, Hole template for FLUSH MOUNT 37501H35 North LUCIFER 2 1/4" (57 mm) LIGHTING COMPANY San Antonio, Texas 78219 3 Phone 12101 227-7329 4 Fax (2101227.4967 EFTA00727800 Project Name: LITTLE SAINT JAMES Item Number: LT-03 Project #: LS3-01 Item Description: CEILING FAN Issue Date: Item Quantity: Manufacturer: TBD Source: Address: Address: Phone: Phone: Fax: Fax: Contact: Contact: E-mail: E-mail: Web: Web: Description: CEILING FAN FOR KITCHEN - TBD, AWAITING CLIENT DECISION ON FANS PRESENTED Required Item(s) for Designer Approval Prior to Fabrication: Seaming Diagram Strike-Off Finish Sample Cutting Shop Dwgs Prototype Flame Certificate Instructions: • The Contractor must coordinate with the manufacturer exact specifications on sockets, lamping, and ADA requirements to ensure decorative light fixtures meet all local, state, and federal codes for applicable conditions. • Property owner is responsible for purchasing and supplying all lamps (bulbs) required for all specified fixtures. Lamping requirements must not exceed the maximum wattage as specified for each fixture. Page 1 LT-03 Mark Zeff 515 W 20th St, 4W New York, NY 10011 p www.markzeff.com EFTA00727801 Project Name: LITTLE SAINT JAMES Item Number: P-01 Project #: LSJ-01 Item Description: DOUBLE BASIN SINK Issue Date: Manufacturer: Franke Consumer Products, Inc. Source: By GC Address: Address: 3050 Campus Drive, Suite 500 Hatfield, PA 19440- Phone: (800) 626.5771 Phone: Fax: Fax: Contact: Contact: E-mail: E-mail: Web: www.frankeconsumerproducts.com Web: Product: ARX12031 Color/Finish: STAINLESS STEEL Size/Dimensions: REFER TO CUTSHEET Required Item(s) for Designer Approval Prior to Fabrication: Seaming Diagram Strike-Off Finish Sample Cutting Shop Dwgs Prototype Flame Certificate Instructions: • Image is for reference only. • Owner must be provided with manual, installation guidelines, and maintenance instructions in addition to warranties if applicable. • All metal to be non-corrosive. • Contractor is to assume responsibility for preparing surfaces and using appropriate techniques and installation methods as required by manufacturer prior to installation. Page 1 P-01 Mark Zeff 515 W 20th St, 4W New York, NY 10011 p www.markzeff.com EFTA00727802 Priin Product http://www.frankeksd.com/printproduct.plip?prodid=738 Er= gholm ARX12031 Scala yaw art ,oma out inlhickety? imagne a Caning), saki sugars or retrial aro.Mbxgraktb.a atilLS WILJI PO uriquOvay at ',Cu gapar0 6:03 OM Man ..43 id/enscame ea: 33' Salm Olmansiont: 38 ST 17" IL 8 VC tnerlor ClininskaK: sr witriexVx0 Ire• Accotoriu more Franke choices V Zi i Pt, reigning ya11001 F81.362482-XS.IB ffP.57➢0 Alignunt (Sart suit, )t I of I 10/20/2010 1:56 PM EFTA00727803 Project Name: LIME SAINT JAMES Item Number: P-01A Project #: LS3-01 Item Description: PULL OUT FAUCET Issue Date: Manufacturer: Grohe Source: Address: 241 Covington Drive Address: Bloomingdale, IL 60108- Phone: Phone: Fax: Fax: Contact: Alan Taranto Contact: E-mail: E-mail: Web: www.grohe.com Web: Product: 33759 SDO Color/Finish: STAINLESS STEEL Size/Dimensions: REFER TO CUTSHEET Required Item(s) for Designer Approval Prior to Fabrication: Seaming Diagram Strike-Off Finish Sample Cutting Shop Dwgs Prototype Flame Certificate Instructions: • Image is for reference only. • Owner must be provided with manual, installation guidelines, and maintenance instructions in addition to warranties if applicable. • All metal to be non-corrosive. • Contractor is to assume responsibility for preparing surfaces and using appropriate techniques and installation methods as required by manufacturer prior to installation. Page 1 P-01A Mark Zeff 515 W 20th St, 4W New York, NY 10011 p www.markzeff.com EFTA00727804 ' GROHE Ladylux Plus . . • „T.; 33 759 High Profile Pull Out Description Single-Handle Kitchen Pull-out GROHE RealSteele stainless steel contruction 360, swivel spout Dual spray control-switches back and forth between regular flow and spray SpeedClean anti-lime system Ceramic cartridge 56" extractable hose 9 1/8" spout reach Quick installation system Stainless steel braided flexible supplies Integral check valves Single hole installation Installation note: For full handle movement when mounted in front of a wall or backsplash, this faucet must be installed with no less than 3 1/4" of clearance between the faucet and backsplash or wall, unless the faucet is installed with the handle facing forward (handle oppposite the wall). IAPMO File #1750 Flow Rate 2.2 gpm at 60 psi, 2.5 gpm at 80 psi (9.5 Ipm) Code Compliance ASME/ANSI A112.18.1M ANSI/NSF Standard 61 ADA Compliant Finish Options 33 759 SDO Stainless Steel 33 759 KDO Stainless Steel/Black GROHE America, Inc 241 Covington Drive, Bloomingdale, IL 60108 630-582-7711 Fax:630-582-7722 GROHE Canada, Inc 1230 Lakeshore Road East, Mississauga, Ontario Canada L5E 1E9 905.271.2929 Fax:905.271.9494 EFTA00727805 Project Name: LITTLE SAINT JAMES Item Number: P-02 Project #: LSJ-01 Item Description: SINGLE BASIN SINK Issue Date: Manufacturer: Franke Consumer Products, Inc. Source: By GC Address: Address: 3050 Campus Drive, Suite 500 Hatfield, PA 19440- Phone: (800) 626.5771 Phone: Fax: Fax: Contact: Contact: E-mail: E-mail: Web: www.frankeconsumerproducts.com Web: Product: PSX1103012/16 Color/Finish: STAINLESS STEEL Size/Dimensions: REFER TO CUTSHEET Required Item(s) for Designer Approval Prior to Fabrication: Seaming Diagram Strike-Off Finish Sample Cutting Shop Dwgs Prototype Flame Certificate Instructions: • Image is for reference only. • Owner must be provided with manual, installation guidelines, and maintenance instructions in addition to warranties if applicable. • All metal to be non-corrosive. • Contractor is to assume responsibility for preparing surfaces and using appropriate techniques and installation methods as required by manufacturer prior to installation. Page 1 P-02 Mark Zeff 515 W 20th St, 4W New York, NY 10011 p www.marlczeff.com EFTA00727806 Print Product hnp://www.frankcksd.comfprintproduct.php?prodid=130 FRANKE hr.„.. b PSX110309/16, PSX1103012/16 If x. auras% (carat laical is forty. a ProSmovi Straw., a rid Virg $1..R cortrona gab aria and wry droo to emormodete to tuky anneal81a wows cas Claua: 16 illeaum Coale Sa: take 1:11anais:: 391.t m18 1ff x9 ltlrw It 7116 Marla Damao:: 31 1.2* x 10 1/2' xi) VW xw.11 NIB Accessories more hake choices... Ct+ 1.530455P PS3036C PSX1203not P3X1203Moti 1 of 1 10/20/2010 1:58 PM EFTA00727807 Project Name: LITTLE SAINT JAMES Item Number: P-03 Project #: LSJ-01 Item Description: POT FILLER Issue Date: Manufacturer: Grohe Source: Address: 241 Covington Drive Address: Bloomingdale, IL 60108- Phone: Phone: Fax: Fax: Contact: Alan Taranto Contact: E-mail: E-mail: Web: www.grohe.com Web: Product: 31041 SOO Color/Finish: STAINLESS STEEL Size/Dimensions: REFER TO CUTSHEET Required Item(s) for Designer Approval Prior to Fabrication: Seaming Diagram Strike-Off Finish Sample Cutting Shop Dwgs Prototype Flame Certificate Instructions: • Image is for reference only. • Owner must be provided with manual, installation guidelines, and maintenance instructions in addition to warranties if applicable. • All metal to be non-corrosive. • Contractor is to assume responsibility for preparing surfaces and using appropriate techniques and installation methods as required by manufacturer prior to installation. Page 1 P-03 Mark Zeff 515 W 20th St, 4W New York, NY 10011 p www.markzeff.com EFTA00727808 GROHE „T... 31 041 Wall Mount Pot Filler Description GROHE RealSteele Stainless Steel Construction 20" jointed swing spout Two 1/4-turn shut-off valves located at wall and outlet GROHE SilkMove® ceramic cartridges Double O-ring seal and bearing joints Anti-rotation wall flange Single-hole installation, cold water only Flow Rate 2.2 at 60 psi, 2.5 at 80 psi (9.5 Ipm) Code Compliance ASME/ANSI A112.18.1M ANSI/NSF Standard 61 Finish Options 31 041 SDO Stainless Steel GROHE America, Inc 241 Covington Drive, Bloomingdale, IL 60108 630-582-7711 Fax:630-582-7722 GROHE Canada, Inc 1230 Lakeshore Road East, Mississauga, Ontario Canada LSE 1E9 905.271.2929 Fax:905.271.9494 EFTA00727809 Project Name: LITTLE SAINT JAMES Item Number: PT-01 Project #: LSJ -01 Item Description: SUPER WHITE, FLAT Issue Date: Manufacturer: Benjamin Moore Source: Address: 101 Paragon Drive Address: Montvale, NJ 07645- Phone: Phone: Fax: Fax: Contact: Rodger Lippman Contact: E-mail: E-mail: Web: www.benjaminmoore.com Web: Product: BENJAMIN MOORE SUPER WHITE Color/Finish: FLAT FINISH Notes: LOCATION: KITCHEN WALL AND CEILING PAINT Required Item(s) for Designer Approval Prior to Fabrication: Seaming Diagram Strike-Off V Finish Sample Cutting Shop Dwgs Prototype Flame Certificate Instructions: • Image is for reference only. • Contractor is to assume responsibility for preparing surfaces and using appropriate techniques and installation methods as required by manufacturer prior to installation. • All paint finishes to be low odor and low VOC when possible. • Primer to be applied to substrate to prepare it for subsequent finish coats. Contractor to consult paint manufacturer for proper primer recommendations. Page 1 PT-01 Mark Zeff 515 W 20th St, 4W New York, NY 10011 p www.markzeff.com EFTA00727810 Project Name: LITTLE SAINT JAMES Item Number: PT-02 Project #: LSJ -01 Item Description: SUPER WHITE, SEMI-GLOSS Issue Date: Manufacturer: Benjamin Moore Source: Address: 101 Paragon Drive Address: Montvale, NJ 07645- Phone: Phone: Fax: Fax: Contact: Rodger Lippman Contact: E-mail: E-mail: Web: www.benjaminmoore.com Web: Product: BENJAMIN MOORE SUPER WHITE Color/Finish: SEMI GLOSS FINISH Notes: LOCATION: KITCHEN000R & TRIM PAINT Required Item(s) for Designer Approval Prior to Fabrication: Seaming Diagram Strike-Off V Finish Sample Cutting Shop Dwgs Prototype Flame Certificate Instructions: • Image is for reference only. • Contractor is to assume responsibility for preparing surfaces and using appropriate techniques and installation methods as required by manufacturer prior to installation. • All paint finishes to be low odor and low VOC when possible. • Primer to be applied to substrate to prepare it for subsequent finish coats. Contractor to consult paint manufacturer for proper primer recommendations. Page 1 PT-02 Mark Zeff 515 W 20th St, 4W New York, NY 10011 p www.markzeff.com EFTA00727811 Project Name: LITTLE SAINT JAMES Item Number: SF-01 Project #: LSJ-01 Item Description: CHANTILLY LACE LACQUER Issue Date: Manufacturer: Benjamin Moore Source: Address: 101 Paragon Drive Address: Montvale, NJ 07645- Phone: Phone: Fax: Fax: Contact: Rodger Lippman Contact: E-mail: E-mail: Web: www.benjaminmoore.com Web: Product: HIGH GLOSS LACQUER Color/Finish: TO MATCH BENJAMIN MOORE #2121.70 CHANTILLY LACE Notes: LOCATION: KITCHEN CABINET EXTERIOR Benjamin Moore Chantilly Lace 2121-70 Required Item(s) for Designer Approval Prior to Fabrication: Seaming Diagram Strike-Off V Finish Sample Cutting Shop Dwgs Prototype Flame Certificate Page 1 SF-01 Mark Zeff 515 W 20th St, 4W New York, NY 10011 p www.markzeff.com EFTA00727812 Project Name: LIME SAINT JAMES Item Number: ST-02 Project #: LS3-01 Item Description: QUARTZ SURFACING Issue Date: Manufacturer: CaesarStone Source: CaesarStone Address: 36-16 19th Ave Address: 36-16 19th Ave Astoria, NY 11105- Astoria, NY 11105- Phone: Phone: Fax: Fax: Contact: Renee Pecquex Contact: Renee Pecquex E-mail: E-mail: Web: www.caesarstoneus.com Web: www.caesarstoneus.com Product: 3141 Color/Finish: EGGSHELL POLISHED Size/Dimensions: 11/4" THICK, SQUARE EDGE Notes: LOCATION: COUNTERTOP AND BACKSRASH Required Item(s) for Designer Approval Prior to Fabrication: Seaming Diagram Strike-Off V Finish Sample Cutting Shop Dwgs Prototype Flame Certificate Instructions: • Image is for reference only. • Owner must be provided with manual, installation guidelines, and maintenance instructions in addition to warranties if applicable. Page 1 ST-02 Mark Zeff 515 W 20th St, 4W New York, NY 10011 p www.markzeff.com EFTA00727813 CRaesarstone Surfaces Quartz GUIDE SPECIFICATION CaesarStone® is a quartz-based fabricated stone which can be used for attractive and functional countertops, shower and tub surrounds, interior wall cladding, and other interior applications. Compared to natural stone surfacing, CaesarStone offers many attractive advantages including greater strength, wear resistance, ease of handling, and a unique aesthetic character. Edit this guide specification according to Project requirements. Samples, product literature, and design assistance are available by contacting CaesarStone at 877-978-2789 or by visiting caesarstoneus.com. Since fabrication and installation of CaesarStone is similar to that of natural stone, publications such as the Marble Institute of America's Dimension Stone Design Manual can also be consulted. SECTION 06 61 19 - QUARTZ SURFACING FABRICATIONS SECTION 12 36 61 - QUARTZ SURFACING COUNTERTOPS PART 1 GENERAL 1.01 SUMMARY Coordinate following with terminology used to identify CaesarStone on Drawings. In most instances, CaesarStone should be called-out as "Quartz Surfacing". A. Section Includes: [Quartz surfacing] [Engineered stone] [Stone] for: 1. Countertops. 2. Interior [wainscoats] [and] [wall cladding]. 3. [Shower] [and] [bath] enclosures. 4. f .1 5. Other interior applications as shown on Drawings. B. Related Sections: See CaesarStone product data for additional guidelines for substrates. 1. Section [06 20 00 — Finish Carpentry:] [06 40 00 - Architectural Woodwork:] [09 20 00 — Plaster and Gypsum Board:]1 - :] Provide framing and blocking to support quartz surfacing within specified tolerances and in accordance with manufacturer's instructions. Retain the following, for example, where a CaesarStone countertop is used with a backsplash of a different material, or where a sink set into a CaesarStone countertop. 2. Section [07 92 00 - Joint Sealers:] F :] Sealers between quartz surfacing and work of other Sections [which are not specified in this Section]. Vernon 3.1. Scplanba 24. 3107 1 EFTA00727814 CRaesarstone Surfaces Quartz GUIDE SPECIFICATION CaesarStone can be used as partitions for toilet and shower compartments. Contact CaesarStone for information. 3. Section [10 21 13 - Stone Toilet Compartments] [10 21 16 - Stone Shower and Dressing Compartments] f :] Quartz surfacing used as toilet room partitions. Templates may be required for sinks and plumbing trim, stove tops, hardware, etc. 4. Templates showing cutouts required for installation of items installed on or penetrating through quartz surfacing shall be provided under Sections where items are specified. [Indicate if [sink] [and] [lavatory] cutouts are for top-mount or undercabinet installation.] 1.02 REFERENCES A. ASTM International: 1. ASTM C97 — Absorption and Bulk Specific Gravity of Dimension Stone. 2. ASTM C99 — Modulus of Rupture of Dimension Stone. 3. ASTM C170 — Compressive Strength of Dimension Stone. 4. ASTM C217 — Weather Resistance of Slate. 5. ASTM C482 — Bond Strength of Ceramic Tile to Portland Cement. 6. ASTM C484 — Thermal Shock Resistance of Glazed Ceramic Tile. 7. ASTM C501 — Relative Resistance to Wear of Unglazed Ceramic Tile by the Taber Abraser. 8. ASTM C531 — Linear Shrinkage and Coefficient of Thermal Expansion of Chemical- Resistant Mortars, Grouts, Monolithic Surfacings, and Polymer Concretes. 9. ASTM C880 — Flexural Strength of Dimension Stone. 10.ASTM C1028 - Static Coefficient of Friction of Ceramic Tile and Other Like Surfaces by the Horizontal Dynamometer Pull-Meter Method. 11.ASTM D256 — Izod Pendulum Impact Resistance of Plastics. 12.ASTM D2047 - Static Coefficient of Friction of Polish-Coated Floor Surfaces by the James Machine. 13.ASTM D2299 — Relative Stain Resistance of Plastics. 14.ASTM E84 - Surface Burning Characteristics of Building Materials. B. International Organization for Standardization: 1. ISO 9002 — Quality systems -- Model for Quality Assurance in Production, Installation and Servicing. 2. ISO 14001 — Environmental Management Systems 3. NSF 1.03 SUBMITTALS A. Product Data: 1. Quartz Surfacing: Submit manufacturer's product data, [sample warranty form,] and fabrication and installation instructions. 2. Accessories: Submit manufacturer's product data and installation instructions. Vernon 3.1. Seine:tea 24. 3107 2 EFTA00727815 Ucaesarstone Surfaces Quartz GUIDE SPECIFICATION B. Shop Drawings: Show field-verified dimensions, quartz surfacing dimensions, locations and dimensions of cutouts, required locations of support and blocking members, edge profiles, and installation details and methods. Identify color[s] and finish[es]. C. Samples: Coordinate Subparagraphs 1. and 2. with the color specifications in Part 2 — Products. 1. [Samples for Color Selection: Submit [two] sets of manufacturer's standard colors and finishes.] 2. Samples for Color Approval: Submit [two] [ 1 samples 10 x 10 inches (250 x 250 mm) of [each] color and finish selected. 3. Stone Adhesive: Submit [two][ samples of an adhesive joint for [each] color quartz surfacing selected. Show color match of adhesive. D. Fabricator Qualifications: Submit evidence of fabricator's qualifications. E. Closeout Submittals: Submit completed warranty form. 1.04 DELIVERY, STORAGE, AND HANDLING A. Packaging, Shipping, Handling, and Unloading: Observe manufacturer's recommendations and handle in manner to prevent breakage or damage. Brace parts if necessary. Transport in the near-vertical position with finished face toward finished face. Do not allow finished surfaces to rub during shipping or handling. B. Storage and Protection: Store in racks in near-vertical position. Prevent warpage and breakage. Store inside away from direct exposure to sun. Store between 25 and 130 QF (- 4 and 54 QC). Store with finished face toward finished face. 1.05 WARRANTY The following is available on single-family residences only and requires use of manufacturer- certified fabricator. A. Provide manufacturer's ten-year limited warranty against product defects when fabricated and installed by a CaesarStone certified fabricator. Vernon 3.1. Scplanba 24. 3107 3 EFTA00727816 Ucaesarstone Quartz Surfaces GUIDE SPECIFICATION PART 2 PRODUCT 2.01 MANUFACTURERS A. Qualifications: Manufacturer shall be ISO 9002 and ISO 14001 certified. B. Acceptable Manufacturer: Provide CaesarStone Quartz Surfacing distributed by U.S. Quartz Products Inc (CaesarStone U.S.A., Inc.); Van Nuys, CA; phone 877-9-QUARTZ; www.caesarstoneus.com. The following product is included as a convenience to specifiers who require multiple suppliers. It is not warranted or recommended by CaesarStone. C. Substitutions: Zodiaq manufactured by DuPont may be substituted in accordance with [Instructions to Bidders.] [Section 01 25 00 - Substitution Procedures.] 2.02 QUARTZ SURFACING A. Composition: 93 percent crushed quartz aggregate combined with resins and pigments and fabricated into slabs using a vacuum vibro-compaction process. CaesarStone can be fabricated in larger sized pieces due to its superior flexural strength compared to natural stone. This may reduce the number of joints in an installation and permit more economical and better looking jobs. It may also allow the use of thinner material, producing additional economies and weight reductions. Thickness: 3/4" is the minimum recommended for countertops; use 1-1/4" material when greater strength or thicker edges are required. Size: If the extra width is required, consult CaesarStone before specifying to assure availability. B. Dimensions: 1. Thickness: Nominal [3/4 inch (20 mm)] (1-1/4 inches (30 mm)] [As shown on Drawings.] 2. Size: Slabs shall be not less than [56.5 x 120 inches (1.44 x 3.05 m)] to minimize number of joints in installation. The back of each slab of CaesarStone is imprinted with a trademarked zigzag pattern to simplify jobsite identification. C. Identification: Material shall be labeled with batch number and imprinted on back with manufacturer's identifying mark. D. Performance: 1. Flexural Strength: 7,420 psi, ASTM C880. 2. Compressive Strength: ASTM C-170 a. Dry: 10,430 psi average. Vernon 3.1. September 24. 3107 4 EFTA00727817 CRaesarstone Surfaces Quartz GUIDE SPECIFICATION b. Wet: 11,265 psi average. 3. Izod Impact Strength: 0.361ft. lbsJinch of notch average; ASTM D256. 4. Bond Strength: 205 psi; ASTM C482 modified. 5. Modulus of Rupture: 2,110 average, ASTM C99. 6. Mohs Hardness: 6.5-7.5; scratch test. 7. Absorption: 0.022%; ASTM C97. 8. Stain and Acid Resistance: Not affected; ASTM D2299. 9. Surface Burning Characteristics: Flame spread = 10, smoke density = 195; ASTM E84. 10. Thermal Shock Resistance: Passes 5 cycles, 75°F-295°F; ASTM C484. 11. Coefficient of Thermal Expansion: 1.36x1O inch per °F.; ASTM C531. 12. Weathering Resistance: Not affected after seven days in 1% sulfuric acid; ASTM C217. 13. Freeze-Thaw Resistance: No visible damage or discoloration after 25 cycles (-45°C to 23°C); S.L.P. with ASTM C62 as guide. 14. Wear Resistance: 36.12 gram average; ASTM C501, tested with 1 kg. load, 1000 cycles at 70 r.p.m. The static coefficient of friction, below, is important for traffic-bearing surfaces and can be deleted when specifying other applications. 15. Static Coefficient of Friction: a. Polished Finish: 0.68 average by ASTM D2047, James Machine; 0.87 average (dry) and 0.54 average (wet) by ASTM C1028, Dynamometer Pull Method. b. Honed Finish: 0.69 average by ASTM D2047, James Machine; 0.73 average (dry) and 0.68 average (wet) by ASTM C1028, Dynamometer Pull Method. Polished CaesarStone: 40 stocked colors. Honed CaesarStone: 9 stocked colors. Note that dark honed colors will show fingerprints and require increased maintenance. Custom Colors and Finishes: Available without additional charge on orders of 4,500 sq. ft. Edit the following according to color selection method and coordinate with submittals. E. Color and Finish: 1. Provide color[s] and [finish[es] selected by [Architect] [ 1 from manufacturer's stocked standards. [Allow for selection of up to [two] [four] [ 1 colors.] 2. Provide custom color and finish to match [sample in [Architect's] U office.] .1 All standard colors are available with polished finish. See color charts or samples for availability of honed finish. 3. Provide [Champagne Limestone, Color No. 2400] , Color No. 1 with [polished] [honed] finish. 4. Finish: Versson 3.1. September 24. 1107 5 EFTA00727818 Ucaesarstone Surfaces Quartz GUIDE SPECIFICATION a. Polished Surface shall have gloss greater than or equal to 35% at 50g. b. Honed Surface shall have a matte finish. Retain the following if edges and corners are not detailed on Drawings. F. Exposed Edges [and Corners]: 1. Countertops: a. Edges: [Square] [Bullnose] [Beveled] [Waterfall] 11 profile, [single] [double] layer thick. b. Outside Corners: [Square.] [[3/4 inch (20 mm)] [ inch[es] ( mm)] radius.] 2. [Backsplash] [and] [Wall Cladding]: a. Edges: [Square.] [ .] b. Outside Corners: [Square butt joints.] [ .] 2.03 ACCESSORIES A. Mounting Adhesives: 1. Provide structural-grade silicone or epoxy adhesives of type recommended by manufacturer for application and conditions of use. 2. Acceptable Silicone Manufactures: a. Dow Corning. b. GE Sealants and Adhesives. c. I 1. 3. Acceptable Epoxy Manufacturers: a. Akemi North America. b. Bonstone Material Corporation. c. Tenax USA. d. 1 1. 4. Provide spacers, if required, of type recommended by adhesive manufacturer. B. Stone Adhesive: 1. Provide epoxy or polyester adhesive of type recommend by manufacturer for application and conditions of use. 2. Acceptable Manufacturers: a. Akemi North America. b. Bonstone Material Corporation. c. Tenax USA. d. I 1. 3. Color: Adhesive which will be visible in finished work shall be tinted to match quartz surfacing. In most countertop and interior cladding applications, CaesarStone can be installed with structural adhesive. Where required, however, CaesarStone can also be set in grout or installed with ties, clips, or other types of hardware recommended for thin stone veneers. Edit below and coordinate Section as required. C. [Fasteners] [Grout] [Hardware]: [ .1 D. Joint Sealants: Vernon 3.1. Seplembet A.1101 6 EFTA00727819 CRaesarstone Surfaces Quartz GUIDE SPECIFICATION 1. Clear silicone sealant of type recommended by manufacturer for application and conditions of use. 2. Provide anti-bacterial type in [[toilet] [and] [bath] rooms,] [food preparation areas,] [and] 1. 3. Acceptable Manufactures: a. Dow Corning. b. GE Sealants and Adhesives. c. 1. E. Solvent: Product recommended by adhesive manufacturer to clean surface of quartz surfacing to assure adhesion of adhesives [and sealants]. F. Cleaning Agents: Non-abrasive, soft-scrub type kitchen cleansers. 2.04 FABRICATION Include manufacturer authorization if manufacturer's warranty is specified. A. Fabricator: Firm shall have five years experience fabricating architectural stone and shall have water-cooled cutting tools. [Firm shall be authorized in writing by manufacturer.] B. Shop Assembly: Observe proper safety procedures and comply with manufacturer's instructions. C. Layout: Layout joints [as shown on Drawings.] [to minimize joints and to avoid L-shaped pieces of quartz surfacing.] D. Inspect Material: 1. Inspect material for defects prior to fabrication. 2. Color Match: Materials throughout Project shall be from the same batch and shall bear labels with same batch number. Visually inspect materials to be used for adjacent pieces to assure acceptable color match. Inspect in lighting conditions similar to those on Project. 3. Variation in distribution of aggregates in quartz surfacing which are within manufacturer's tolerances is not a defect. E. Tools: Cut and polish with water-cooled power tools. F. Cutouts: As with any type of stone, smaller radii increase potential for crack propagation at inside corners; in no case should radius less than 3/8 inch be used. 1. Cutouts shall have [3/8 inches (10 mm)] f inches ( mm)] minimum inside corner radius. Inside corners shall be reinforced in an acceptable manner to prevent cracking. 2. Where edges of cutout will be exposed in finished work, polish edges. Versson 3.1. Scplanba 24. 3107 7 EFTA00727820 @Caesars-tone Quartz Surfaces GUIDE SPECIFICATION The following is recommended in areas subject to heavy service or where additional strength is justified. 3. [If the remaining material outside a cutout is less than [three inches (76 mm)) inches ( mm)J wide, reinforce area by laminating it with a strip of quartz surfacing.] G. Laminations: Laminate layers of quartz surfacing as required to create built-up [edges,] [trim,] [and other areas requiring additional thickness]. Vernon 3.1. Scplanba 24. 3107 8 EFTA00727821 Ucaesarstone Quartz Surfaces GUIDE SPECIFICATION PART 3 EXECUTION 3.01 ACCEPTABLE INSTALLER A. Installer: Firm shall have five years experience installing architectural stone. 3.02 EXAMINATION A. Site Verification: 1. Verify dimensions by field measurements prior to fabrication. 2. Verify that substrates supporting quartz surfaces are plumb, level, and flat to within 1/16 inch in ten feet (1.6 mm in 3000 mm) and that necessary supports and blocking are in place. 3. [Base Cabinets: Cabinet units shall be securely fixed to adjoining units and back wall.] B. Inspect finished surfaces for damage. Do not install until damage materials have been repaired in an acceptable manner or replaced. 3.03 PREPARATION A. Protect finished surfaces against scratches. Apply masking where necessary. Guard against grit, dust, and other trades. Retain following if quartz surfacing is to be installed on existing countertops or walls. B. Remodeling: 1. Where necessary, remove existing [countertops] [and] [materials to be demolished] in accordance with [Section 02 42 00 — Removal and Salvage of Construction Materials] 2. Verify that remaining construction is of sufficient strength and tolerances to support quartz surfacing and make necessary repairs. 3. [Disconnect utilities as specified in other sections.] 3.04 INSTALLATION A. Install materials in accordance to manufacturer's recommendations. Lift and place to avoid breakage. B. Preliminary Installation and Adjustment: Position materials to verify that materials are correctly sized and prepared. Make necessary adjustments. 1. If jobsite cutting, grinding, or polishing is required, use water-cooled tools. Protect jobsite and surfaces against dust and water. Perform work away from installation site if possible. 2. Countertops: Gypsum drywall back walls [which are not [fire] [or] [acoustically] rated] may be routed up to half the thickness of the drywall to allow countertop to fit. 3. Allow gaps for expansion of not less than 1/16 inch (1.5 mm) per five feet when installed between walls or other fixed conditions. 4. [Drainage: [Adjacent to sinks] [and] [where drainage is required], shim countertops slightly to insure positive drainage.] Vernon 3.1. Sepkneel 24. 3107 9 EFTA00727822 CRaesarstone Surfaces Quartz GUIDE SPECIFICATION C. Permanent Installation: 1. After verifying fit, remove quartz surfacing from position, clean substrates of dust and contamination, and clean quartz surfacing back side and joints with solvent. 2. Apply sufficient quantity of mounting adhesive in accordance with adhesive manufacturer's recommendations to provide permanent, secure installation. 3. Spacing of mounting adhesive shall not exceed: a. Horizontal Surfaces: 1 1 inches ([ 1 mm) on center. b. Vertical Surfaces: [ 1 inches (1 1mm) on center; provide temporary shims until adhesive cures. 4. [Fasteners] [Grout] [Hardware]: [ 5. Install surfacing plumb, level, and square and flat to within 1/16 inch in ten feet (1.6 mm in 3000 mm). D. Joints: 1. Joints Between Adjacent Pieces of Quartz Surfacing: a. Joints shall be flush, tight fitting, level, and neat. b. Securely join with stone adhesive. Fill joints level with quartz surfacing. c. Clamp or brace quartz surfacing in position until adhesive sets. 2. Joints [Between Backsplashes and Countertops] [and] [Around [Tub] [and] [Shower] Enclosures]: Seal joints with silicone sealer. 3.05 REPAIR A. Repair or replace damaged materials in a satisfactory manner. 3.06 CLEANING A. Remove masking and excess adhesives and sealants. Clean exposed surfaces. 3.07 PROTECTION A. Protect surfacing from damage by other Sections. Use below if Drawings do not adequately specify scope of Work or locations of CaesarStone products. The following is an example only. 3.08 SCHEDULES C. Toilet Rooms — Rooms 102 and 103: 1. Countertops: CaesarStone Sierra, Color 9255; 3/4" thick; waterfall front edge. 2. Wainscoat: CaesarStone Baja, Color 3200; 3/4" thick; square top edge and butt joint corner. D. Lobby - Room 101 1. Reception Desk: CaesarStone Concrete, Color 2003 a. Countertops: Polished finish,1-1/4" thick; bullnosed exposed edges. b. Vertical Cladding: Honed finish, 3/4" thick, quirk joints. 2. Wall Behind Desk: Copper Canyon, Color 9480; 3/4" thick; see drawings for edge trim and sandblasted graphics. Vernon 3.1. September 24. A107 10 EFTA00727823 CRaesarstone Quartz Surfaces GUIDE SPECIFICATION END OF SECTION © 2007, U.S. Quartz Products Inc. - CaesarStone USA, Inc. Qualified design and construction professionals may copy this document for the purpose of creating construction specifications or purchase orders for materials manufactured by CaesarStone. Verston 3.1. Seine:tea 24. 3107 11 EFTA00727824 Project Name: LITTLE SAINT JAMES Item Number: T-O1 Project #: LSJ-O1 Item Description: 24" x 24" CAESARSTONE TILE Issue Date: Manufacturer: CaesarStone Source: CaesarStone Address: 36-16 19th Ave Address: 36-16 19th Ave Astoria, NY 11105- Astoria, NY 11105- Phone: Phone: Fax: Fax: Contact: Renee Pecquex Contact: Renee Pecquex E-mail: E-mail: Web: www.caesarstoneus.com Web: www.caesarstoneus.com Product: #1141 Color/Finish: PURE WHITE, POLISHED Size/Dimensions: SLAB CUT TO 24"x24"x3/4" TILE Grout: STANDARD WHITE Required Item(s) for Designer Approval Prior to Fabrication: Seaming Diagram Strike-Off V Finish Sample Cutting Shop Dwgs Prototype Flame Certificate Instructions: • Image is for reference only. Page 1 T-O1 Mark Zeff 515 W 20th St, 4W New York, NY 10011 p www.markzeff.com EFTA00727825